Mediacom Remote Control Manual & Setup Guide

A wide range of services and devices are offered by Mediacom Communications. The list includes phones, universal remotes, cable TV services, and internet services. Cable television service comes with the added benefit of universal remote control.

Yes! You read it correctly, and the Mediacom Cable Remote is no ordinary network remote control. It’s a universal remote. Universal remotes are very useful, and they make operating various devices convenient and hassle-free.

Mediacom Remote Control Manual

They eliminate the need to have a separate remote control for each device. The remote only needs to be programmed into the device you wish to operate with the universal remote. It comes pre-programmed to work with the cable box. Programming is only needed to operate the additional devices. Just follow the below steps:

To Program the DRC800 Remote:

 STEP 1:Turn on the device you want to program to use with the remote (ex: If you want to set up the remote for the DVD player then switch on the DVD player manually)

STEP 2: Now, on the top of the remote, from the various mode buttons (TV, DVD/VCR, Audio and Cable), press and hold the one which matches your device until the LED lights up.

STEP 3: Next, press the power button of the remote. The illuminating LED will blink thrice and then will stop lighting.

STEP 4: Direct the remote at the device and press the “CH+” key until it turns off.

STEP 5: To save the program, click “OK.”

STEP 6: This will save the correct code of the device with the remote.

To Program the Atlas DVR or Atlas OCAP Remote:

STEP 1: Turn on the device you want to program to use with the remote (ex: If you want to set up the remote for the DVD player then switch on the DVD player manually)

STEP 2: Now, on the top of the remote, from the various mode buttons (TV, DVD, AUX, AUD, and CBL), press the one which matches your device until the LED corresponding to the mode flashes.

STEP 3: Also press and hold the “SETUP” button while entering three digits 9-9-1 code till the same LED light flashes two times.

STEP 4: Place the remote towards to the device and press the “CH+” button until it shuts off.

STEP 5: To permanent the setup, press “SETUP.”

4-digits Mediacom remote setup codes

5-digits Mediacom Remote setup codes.

Mediacom Cable codes for RCA remote

Rca Universal Remote Codes 5 Digit

Mediacom Cable code for GE remote

Mediacom Cable code for One for All remote

Mediacom Cable codes for Philips remote

How can I fix my Mediacom remote that won’t work?

The Mediacom remote may be fixed in a number of ways. Resetting the remote is one of them. You could also think about resetting your TV, DVR, or Mediacom set box. If none of these solutions work, you might want to contact Mediacom.

GE Universal Remote Codes For Onn TV – Step-by-Step Guide

What are the Mediacom remote codes?

Check out these Mediacom codes:

How do you reset your Mediacom universal Remote ?

To reset your Mediacom remote, you must follow the given steps 

Tap on the TiVo button and Pause button concurrently for about five seconds. The purple mild turns on.

2. Insert the wide variety zero of your Mediacom remote control.

3. This process will reset your Mediacom remote.

How do you fix a Television that is not responding to the Remote Control?

You have to replace the remote control batteries, whether it is (AAA or AA batteries) with new first-class batteries. Next, reset the television by unplugging its power wire from the electrical socket. Then, you have to wait for five minutes. Plug the TV power cord into the wall outlet. Check whether the remote is working with the TV.

How do you fix the Mediacom Remote Control not working?

There are various steps to fix the Mediacom remote that does not respond to the Device. One of the methods is to reset the remote. You can also restart your Device, whether it is a TV, DVD, VCR or Mediacom set-top box. If none of the above works, you must contact Mediacom.